사이클의 名家. 느낌이 있는 Shop
 
 
CompleteBicycle
Frame
Components
Tools
Accessories
Apparel
HotSales
|
|
Adjustable Spacer (1+1/8 inch)
프라블럼 솔버 높이조절 스페이서
   
소비자가
25,400원
참고사항 1개 가격
제조사 Problem Solvers (프라블럼 솔버)
원산지 USA
제품코드 HSSPPS01
현재 선주문만 가능합니다.
주문하기전, 배송일정을 꼭! 확인하세요.
주문수량
Steerer Tube1+1/8 inch
ColorBlack
Thickness10 ~ 12 mm
MaterialAlloy
Weight16.0g


높이 조절이 가능한 스페이서입니다.

헤드셋 유격 조절을 위해서, 더이상 헤드셋 탑캡볼트와 스템볼트를 풀었다 조였다 할 필요가 없습니다.

나사산이 없는 방식의 헤드셋을 사용할 때,
헤드셋 캡을 이용해서 유격을 제어할 수 없을 경우에도 사용할 수 있습니다.

스템 컬럼 어댑터를 이용해서 스티어러 튜브를 연장하는데 사용할 수도 있습니다.


* 사용법 *
1. 스템과 헤드셋 사이에 일반적인 스페이서처럼 끼워넣는다.
2. 스템을 최대한 누른 후, 헤드셋 탑캡과 스템 볼트를 고정한다.
3. 고정 볼트를 풀어둔 상태에서, 스페이서를 돌려서 높이를 조절한 다음 고정볼트를 조인다.

※ 스페이서를 돌리기 위해서는 36㎜ 스패너가 필요합니다.


•Installs between stem and headset to adjust headset preload
•Use instead of star nut or preload compression plug; ideal for carbon steerers
•Requires a minimum of 10mm stack height below stem

INSTALLATION

1) Disassemble the adjustable spacer. Lightly grease the threads of the bolt, lockring, and adjusting nut. Reassemble the spacer, threading the lockring onto the adjusting nut completely.
2) Remove the stem and approximately 10mm of headset spacers from fork steerer tube (if applicable). Install the adjustable spacer onto the steerer tube. There is no “up” or “down” configuration. Headset spacers may be installed above and/or below the adjustable spacer.
3) Reinstall the stem onto fork. The top of the stem should be flush with or up to 3mm above the top of the steerer tube. Make sure all of the headset components, adjustable spacer, headset spacers, and stem are seated by pushing the front wheel into the ground and sliding all components down the steerer tube. Align the stem and tighten the steerer clamp bolts to stem manufacturer’s torque specifications.
4) Using 36mm headset wrenches, adjust the spacer to tension the headset. Hold the lockring in place and thread the adjusting nut out of the lockring. Adjust the nut so that all play in the headset bearings has been removed but the headset still turns freely. Hold the handlebar and front brake and press the front of the bike into the ground to check for headset play. Turn the handlebars 45 degrees from center and check (in both directions) for headset play in the same manner. The headset bearings should not bind when the handlebars are turned all the way in either direction. Readjust the spacer as necessary. Do not turn the adjusting nut more than 2 full revolutions from the fully closed position—doing so will result in inadequate thread engagement on the adjustable spacer. If the nut needs to be rotated more than 2 revolutions to remove headset play, remove the stem and add an additional 1 to 2mm of headset spacers. Go back to Step 2 and readjust the spacer.
5) When headset play has been removed, tighten the bolt on the lockring using the 2mm allen wrench. Turn the bolt until snug. The bolt should be tight enough to prevent movement in the
adjusting nut (check with 36mm wrenches).
6) After your first ride, recheck the adjustment of your headset and adjustable headset spacer. Recheck adjustment every 3-5 rides.


개인정보취급방침
Photos Techinical Tips Manuals Columns 1:1상담게시판 ֹ주문/배송조회 장바구니 찜한제품보기 고객센터 주문/배송조회 장바구니 로그인